Miles Mathis' Charge Field
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Earth Batteries and 3-D Printable Graphene

3 posters

Go down

Earth Batteries and 3-D Printable Graphene Empty Earth Batteries and 3-D Printable Graphene

Post by Cr6 Sun Apr 29, 2018 12:22 am

Earth Batteries with Graphene could be interesting along with MIT's new solar crystals in terms of Mathis' Charge Field. Maybe printout a few rods and bury them N-S?  There might be room to play with a new form of these batteries using graphene.

Potential differences of metals
(Soil galvanic series)
Magnesium (pure) -1.75
Magnesium (alloy) -1.60
Zinc -1.10
Aluminum (alloy) -1.05
Aluminum (pure) -0.8 22
Steel (clean) -0.50 to -0.80
Steel (rusted) -0.20 to -0.50
Cast Iron -0.50
Lead -0.50
Steel (concrete) -0.20
Copper -0.20
Brass -0.20
Bronze -0.20
Steel (mill scale) -0.20
Cast iron (high silicon) -0.20
Carbon +0.30
Graphite +0.30
Coke +0.30
Notes: Non-uniform conditions at node surface results in different voltages

From John Bedini's website:
Earth Batteries and 3-D Printable Graphene Snoww1
Earth Batteries and 3-D Printable Graphene Earthbattj2
http://johnbedini.net/john34/earthbatt.html
---------

The article below mentions N-S depths and distances of rods to get more charge output -- that appears curious.
---------
Earth Batteries (from Wikipedia)


An Earth battery is a pair of electrodes made of two dissimilar metals, such as iron and copper, which are buried in the soil or immersed in the sea. Earth batteries act as water activated batteries and if the plates are sufficiently far apart, they can tap telluric currents. Earth batteries are sometimes referred to as telluric power sources and telluric generators.


Operation and use


The simplest earth batteries consist of conductive plates from different metals of the electropotential series, buried in the ground so that the soil acts as the electrolyte in a voltaic cell. As such, the device acts as a primary cell. When operated only as electrolytic devices, the devices were not continuously reliable, owing to drought condition. These devices were used by early experimenters as energy sources for telegraphy. However, in the process of installing long telegraph wires, engineers discovered that there were electrical potential differences between most pairs of telegraph stations, resulting from natural electrical currents (called telluric currents[4]) flowing through the ground. Some early experimenters did recognize that these currents were, in fact, partly responsible for extending the earth batteries' high outputs and long lifetimes. Later, experimenters would utilize these currents alone and, in these systems, the plates became polarized.

It had been long known that continuous electric currents flowed through the solid and liquid portions of the Earth,[5] and the collection of current from an electrically conductive medium in the absence of electrochemical changes (and in the absence of a thermoelectric junction) was established by Lord Kelvin.[6][7] Lord Kelvin's "sea battery" was not a chemical battery.[7] Lord Kelvin observed that such variables as placement of the electrodes in the magnetic field and the direction of the medium's flow affected the current output of his device. Such variables do not affect battery operation. When metal plates are immersed in a liquid medium, energy can be obtained and generated,[8] including (but not limited to) methods known via magneto-hydrodynamic generators. In the various experiments by Lord Kelvin, metal plates were symmetrically perpendicular to the direction of the medium's flow and were carefully placed with respect to a magnetic field, which differentially deflected electrons from the flowing stream. The electrodes can be asymmetrically oriented with respect to the source of energy, though.

To obtain the natural electricity, experimenters would thrust two metal plates into the ground at a certain distance from each other in the direction of a magnetic meridian, or astronomical meridian. The stronger currents flow from south to north. This phenomenon possesses a considerable uniformity of current strength and voltage. As the Earth currents flow from south to north, electrodes are positioned, beginning in the south and ending in the north, to increase the voltage at as large a distance as possible.[9] In many early implementations, the cost was prohibitive because of an over-reliance on extreme spacing between electrodes.

It has been found that all the common metals behave relatively similarly. The two spaced electrodes, having a load in an external circuit connected between them, are disposed in an electrical medium, and energy is imparted to the medium in such manner that "free electrons" in the medium are excited. The free electrons then flow into one electrode to a greater degree than in the other electrode, thereby causing electric current to flow in the external circuit through the load. The current flows from that plate whose position in the electropotential series is near the negative end (such as palladium). The current produced is highest when the two metals are most widely separated from each other in the electropotential series, and when the material nearer the positive end is to the north, while that at the negative end is towards the south. The plates, one copper and another iron or carbon, are connected above ground by means of a wire with as little resistance as possible. In such an arrangement, the electrodes are not appreciably chemically corroded, even when they are in earth saturated with water, and are connected together by a wire for a long time.[citation needed]

It had been found that to strengthen the current, it was most advantageous to drive the northerly electropositive electrode deeper into the medium than the southerly electrode. The greatest currents and voltages were obtained when the difference in depth was such that a line joining the two electrodes was in the direction of the magnetic dip, or magnetic inclination. When the previous methods were combined, the current was tapped and utilized in any well-known manner.[citation needed]

In some cases, a pair of plates with differing electrical properties, and with suitable protective coatings, were buried below the ground. A protective or other coating covered each entire plate. A copper plate could be coated with powdered coke, a processed carbonaceous material. To a zinc plate, a layer of felt could be applied. To use the natural electricity, earth batteries fed electromagnets, the load, that were part of a motor mechanism.[citation needed]

Earth batteries are not to be confused with soil-based microbial fuel cells, which rely on electrogenic micro-organisms present in soil to generate electricity, as opposed to the galvanic reaction of two different metals.[10]

https://en.wikipedia.org/wiki/Earth_battery

Cr6
Admin

Posts : 1178
Join date : 2014-08-09

https://milesmathis.forumotion.com

Back to top Go down

Earth Batteries and 3-D Printable Graphene Empty Re: Earth Batteries and 3-D Printable Graphene

Post by Ciaolo Sun Apr 29, 2018 6:33 am


Ciaolo

Posts : 143
Join date : 2016-09-08

Chromium6 likes this post

Back to top Go down

Earth Batteries and 3-D Printable Graphene Empty Re: Earth Batteries and 3-D Printable Graphene

Post by Chromium6 Sun Aug 29, 2021 8:31 pm

A link that Lloyd provided on his Science Links page has Japanese researchers looking into Ferromagnetic energy harvesting: https://phys.org/news/2021-08-energy-harvesting-technology-based-ferromagnetic.html

Chromium6

Posts : 708
Join date : 2019-11-29

Back to top Go down

Earth Batteries and 3-D Printable Graphene Empty Re: Earth Batteries and 3-D Printable Graphene

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum